cisco2610

[复制链接]
查看11 | 回复9 | 2005-2-28 12:57:00 | 显示全部楼层 |阅读模式
我在一台cisco 2610加了VWIC-2MFT-G703小卡,计划用此卡连通信设备的2M口,可我怎么看不到 intterface serial 0/0 一类的口,只能看到controller e1 0/0等,我怎么配此口的地址呢?急人!
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
using e1 or using ce1
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
记得应该是端口 F0/0 和 F0/1
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
controller E1 0/0在这种方式下不能做ce1使用
framing no-crc4
channel-group 0 timeslots 1-31
用interface Serial0/0:0即可
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
我在2610的S口配的10。14。200。133,在远端的3745的相应S口配10。14。200。134,中间是中兴的ONU设备的2M口,之间用同轴连,最好的时候在26上的以太网口能PING10。14。200。133且时通时断,但一直PING不通10。14。200。134 ,我看了show inter中2610的物理UP但line protocol时DOWN时UP,在远处的3745show inter 物理一直UP,line protocol 是一直down,不知为何?求助
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
在路由器上ping S口时通时段?
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
最好把双端的配制都贴主来,另外双端E1的E1接口参数上必须完全一致,特性参数主要有阻抗/ 帧结构/CRC4校验,阻有75ohm和120ohm两种,帧结构有PCM31/PCM30/不成帧三种
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
2610的配置:
Current configuration : 854 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no network-clock-participate slot 1
no network-clock-participate wic 0
no aaa new-model
ip subnet-zero
ip cef
!
!
!
no ftp-server write-enable
controller E1 0/0
line-termination 75-ohm
channel-group 0 unframed
!
controller E1 0/1
!
!
interface FastEthernet0/0
ip address 10.14.131.66 255.255.255.0
duplexauto
speed auto
interface Serial0/0:0
ip address 10.14.200.133 255.255.255.0
encapsulation ppp
!
interface Async3
no ip address
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.14.200.134
ip http server
!
!
line con 0
line 3
stopbits 1
speed 115200
flowcontrol hardware
line aux 0
line vty 0 4
password cisco
login
transport preferred none
end
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
3745的配置
zhongxin#show runn
Building configuration...
Current configuration : 3103 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname zhongxin
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$neRd$JGpjXjbnHNIyGqBk.mHw80
!
username cisco password 0 cisco
no network-clock-participate slot 1
no network-clock-participate slot 2
no network-clock-participate slot 3
no network-clock-participate slot 4
no network-clock-participate wic 0
no network-clock-participate wic 1
no aaa new-model
ip subnet-zero
ip cef
!

no ftp-server write-enable
-!
!
controller E1 0/0
!
controller E1 0/1
!
controller E1 0/2
!
controller E1 0/3
!
controller E1 1/0
channel-group 0 unframed
!
controller E1 1/1
channel-group 0 unframed
!
controller E1 1/2
channel-group 0 unframed
!
controller E1 1/3
channel-group 0 unframed
!
controller E1 2/0
!
controller E1 2/1
!
controller E1 2/2
!
controller E1 2/3

controller E1 3/0
channel-group 0 unframed
!
controller E1 3/1
channel-group 0 unframed
!
controller E1 3/2
channel-group 0 unframed
!
controller E1 3/3
channel-group 0 unframed
!
controller E1 4/0
channel-group 0 unframed
!
controller E1 4/1
channel-group 0 unframed
!
controller E1 4/2
channel-group 0 unframed
!
controller E1 4/3
channel-group 0 unframed
!
!
interface FastEthernet0/0
ip address 10.14.132.1 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
description jincheng
ip address 10.14.131.130 255.255.255.0
duplex auto
speed auto
!
interface Serial1/0:0
description changzhinan
ip address 10.14.200.114 255.255.255.252
encapsulation ppp

interface Serial1/1:0
description changzhixian
ip address 10.14.200.118 255.255.255.252
encapsulation ppp
Interface Serial3/0:0,
description gaoping
ip address 10.14.200.122 255.255.255.252
encapsulation ppp
!
interface Serial1/3:0
description nanyicheng
ip address 10.14.200.126 255.255.255.252
encapsulation ppp
!
interface Serial3/0:0
description jincun
ip address 10.14.200.130 255.255.255.252
encapsulation ppp
!
interface Serial3/1:0
description jinchengdong
ip address 10.14.200.134 255.255.255.252
encapsulation ppp
!
interface Serial3/2:0
no ip address
encapsulation ppp
!
interface Serial3/3:0
no ip address
encapsulation ppp
!
interface FastEthernet4/0
no ip address
shutdown
duplex auto
speed auto
!
-interface Serial4/0:0
no ip address
encapsulation ppp
!
interface FastEthernet4/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial4/1:0
no ip address
encapsulation ppp
!
interface Serial4/2:0
no ip address
encapsulation ppp
!
interface Serial4/3:0
no ip address
encapsulation ppp
!
ip classless
ip route 10.14.130.0 255.255.255.0 10.14.200.113
ip route 10.14.130.0 255.255.255.0 10.14.200.117
ip route 10.14.130.0 255.255.255.0 10.14.200.121
ip route 10.14.130.0 255.255.255.0 10.14.200.125
ip route 10.14.131.0 255.255.255.0 10.14.200.129
ip route 10.14.131.0 255.255.255.0 10.14.200.133
ip route 10.14.131.0 255.255.255.0 FastEthernet0/1
ip http server
!
!
line con 0
line aux 0
line vty 0 4
password
login
transport preferred none
!
end
回复

使用道具 举报

千问 | 2005-2-28 12:57:00 | 显示全部楼层
现在的情况是我在E1口封装PPP后无论是3745还是2610上的口line protocol dowm,物理UP,一改为HDLC后line protocol就UP 了,即不改前不能PING通本机的S口,改后就能PING通了,但时通时断
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

主题

0

回帖

4882万

积分

论坛元老

Rank: 8Rank: 8

积分
48824836
热门排行